Cdn TM23-S - Direct ENtry Timer & Clock EN Bedienungsanleitung PDF herunterladen

Features

• Dual function

• Counts up & down

• Big digit

• Clock

• Direct entry

• Loud and long alarm

• Stop and restart

• Last count recall

• Counts up after zero

• Counts last min in seconds

• Brushed stainless steel nish

• International time

• 2-way mounting: magnet/stand

• Battery and instructions included

Note: Remove sticker from display before use.

Note: In the following instructions, names of the control

buttons are shown in CAPS. Function information that appears

on the display is shown in BOLD CAPS.

Battery Installation

Replace battery when LCD becomes dim or alarm

level declines.

1. Remove battery door in back by sliding down in

direction of arrow.

2. Install 1.5V AAA battery observing polarity

shown in compartment. The display shows all

segments and a “beep” sounds.

3. Replace battery door.

Operating Instructions

A. Set Clock

1. Press, and hold the CLOCK button until

24 Hr ashes. Press the START/STOP button

to switch between 12 Hr and 24 Hr.

2. To set 12 Hr, AM/PM time, press the CLOCK

button while 12 Hr is ashing. AM will appear

and will ash. To switch between AM and PM,

press START/STOP.

3. To set AM time, press CLOCK while AM is

ashing. Press CLOCK again, and the rst

digit will ash. To enter time, for example,

09:45:00, enter 0 9 4 5 0 0.

4. To set PM time, press CLOCK while PM is

ashing. Press CLOCK again, and the rst digit

will ash. To enter time, for example, 11:30:00,

enter 1 1 3 0 0 0.

5. To set 24 Hr time, press CLOCK while 24 Hr is

ashing. Press CLOCK again and enter the time

directly. For example, to set 23:30:00, enter

2 3 3 0 0 0.

6. The clock will start automatically.

7. The Timer and/or Count Up function will

operate even though the display in the CLOCK

mode. To alert the user in this case, TIMER

and/or COUNT UP will ash on the display

as a reminder.

B. Count Down

1. Press the TIMER button.

2. TIMER will appear on the display.

3. Enter the time to be counted on the 1 – 0

keypad. For example, to count 3 minutes

exactly, enter 3 0 0 for three minutes, zero

seconds. To count 9 hours, 45 minutes and

30 seconds, enter 9 4 5 3 0.

4. Press START/STOP to start the count down.

Press START/STOP button to interrupt

the count. Press START/STOP button again

to resume the count.

5. To clear the count before reaching zero, stop

the count by pressing START/STOP. Then press

the CLEAR button.

Note: The count must rst be stopped to prevent

accidental clearing of the display.

6. On reaching zero the alarm will sound for one

minute, the display will ash and will start

Model: TM23-S

Direct Entry Timer & Clock

Counts 24 hours by minutes & seconds

1 2

Inhaltsverzeichnis

Seite 1 - Operating Instructions

Features• Dual function• Counts up & down• Big digit• Clock• Direct entry• Loud and long alarm• Stop and restart• Last count recall• Coun

Seite 2 - Care of Your Product

to count up to indicate the overtime since reaching zero. The maximum overtime is 10 hours.7. When START/STOP is pressed the amount of overtime will

Kommentare zu diesen Handbüchern

Keine Kommentare

Cdn TM23-S - Direct ENtry Timer & Clock EN Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Relais Cdn TM23-S - Direct ENtry Timer & Clock EN herunter. CDN TM23-S - Direct ENtry Timer & Clock EN User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Relais Cdn TM23-S - Direct ENtry Timer & Clock EN